6000watt Professional Stereo Power Amplifier with DSP

The Crown XTi6002 is a 6000watt power amplifier with DSP that sets new standards for portable sound amplification. Offering increased control, an enhanced feature set and a sleeker design, the Crown XTi-6002 eliminates the need for external crossovers, limiters, and EQs, immediately saving rack space and money.

The Crown XTi 6002 features enhanced control with Crown’s revolutionary PeakX Plus limiters. The limiters are derived from the same framework as those found in I-Tech HD and the new XLS DriveCore Series amplifiers allowing users to manipulate threshold, attack and release times. A new and improved subharmonic synthesizer offers more accurate control over which frequencies are targeted and can be tailored for a specific system or room setup.

Crown XTi6002 Features:

• Peakx Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
• Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
• 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
• New system monitoring provides software visibility of AC line voltage and power supply temperature
• Integrated cast-aluminum handles for easy handling and enhanced durability
• Locking power cord clip provides a secure connection between the amplifier and power cord
• Updated HiQnet Band Manager™ and System Architect™ control software
• Increased number of presets to a total of 30; 29 of which are user definable
• Input EQ: 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
• Crossover Filters: Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
• Output EQ: 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
• Delay: For signal alignment of driver; 50 mS of total delay.
• SubHarmonic Synth: Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
• Peakx™ Plus Limiter: User defeatable limiter that allows users to control Threshold, Attack, and Release times.
• Presets: 30 total presets, 29 of which are user-definable.

Crown XTi6002 Specifications:

• Output Power 2 ohms Stereo (per ch): 3000W
• Output Power 4 ohms Stereo (per ch): 2100W
• Output Power 8 ohms Stereo (per ch): 1200W
• Output Power 8 ohms Bridged-Mono: 4200W
• Output Power 4 ohms Bridged-Mono: 6000W
• Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
• Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
• Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 103 dB (A weighted)
• Total Harmonic Distortion (THD): < 0.5%
• Damping Factor 20 Hz to 1 kHz: > 500
• Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
• Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
• Maximum Input Signal: +22 dBu typical
• Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing)
• Level Control: Two front-panel rotary level controls, one for each channel
• Power Switch Control: On/Off switch applies AC power to the amplifier
• Sel/Prev/Next Buttons Controls: Three buttons near the LCD screen that are used to access menu items and front panel lockout
• LCD Screen: Backlit liquid crystal display that shows preset and processing status
• Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
• –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.
• –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
• Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
• Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
• Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
• Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
• Input Connectors: XLR, one per channel
• Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
• Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
• HiQnet™ USB Connector: Type B, connects to HiQnet™ network.
• Chassis: Steel
• Front Panel: Cast-aluminum
• Cooling: Proportional speed fan with front-to-rear airflow.
• Dimensions: 19" (W) x 3.5" (H) x 16.2" (D)
• Net Weight: 24.0 lbs (10.9kg)
• Shipping Weight:  30.0 lbs (13.6kg)